Reconstitute HGH (Somatropin).
Free HGH (Somatropin) reconstitution calculator. Enter your vial mass and bacteriostatic water for the concentration, draw volume, and exact U-100 syringe units, with a live syringe visualizer. Research use only.
What are you reconstituting?
/How many milligrams are in your vial?
How much bacteriostatic water are you adding?
How much do you want per aliquot?
Which insulin syringe do you have?
Add vial cost for cost per aliquot
Reference figures. Verify all calculations independently before laboratory use. 1 mL = 100 U-100 units. This tool does not recommend a dose, frequency, or protocol.
How to reconstitute HGH (Somatropin).
HGH (somatropin) is a recombinant growth-hormone research protein. Unlike most research peptides, it is conventionally labeled and sold in IU (international units) rather than milligrams — 1 mg is approximately 3 IU per the WHO international standard for somatropin.
- Add bacteriostatic water. Swab the tops of both the HGH (Somatropin) vial and the bacteriostatic water vial. Draw your chosen water volume, then inject it slowly down the inside wall of the HGH (Somatropin) vial so it runs onto the powder rather than splashing onto it.
- Let it dissolve. Let the HGH (Somatropin) dissolve on its own, swirling gently if needed. Do not shake — shaking foams the solution and can stress the peptide. Within a minute or two you should have a clear solution (white lyophilized powder dissolves to a clear liquid).
- Read the concentration. Your concentration is the vial mass divided by the water you added. 3.3 mg in 1 mL of bacteriostatic water is 3.3 mg/mL (3,300 mcg/mL). Enter your own numbers in the calculator above to get the draw volume and U-100 syringe units for any research quantity.
Bacteriostatic water and concentration
The volume of bacteriostatic water you add is the only thing that sets the concentration — the vial mass is fixed. More water means a lower concentration and a larger, easier-to-measure draw. Here is how common HGH (Somatropin) vial sizes land at a 1 mL fill:
| Vial mass | BAC water | Concentration | (mcg/mL) |
|---|---|---|---|
| 3.3 mg | 1 mL | 3.3 mg/mL | 3,300 mcg/mL |
| 8 mg | 1 mL | 8 mg/mL | 8,000 mcg/mL |
Researchers commonly use 1–2 mL of bacteriostatic water for HGH (Somatropin). Any volume in that range works; it only changes how concentrated the vial is and how large the draw will be.
Storage, stability and handling
- HGH vials are most commonly sold labeled in IU (commonly 10 IU per vial). Convert to milligrams before using this calculator: 10 IU is about 3.3 mg, 24 IU is about 8 mg.
- HGH is more agitation-sensitive than most research peptides. Inject the bacteriostatic water slowly down the vial wall and swirl gently — never shake. Shaking can visibly cloud the solution.
- Keep the lyophilized vial refrigerated and protected from light. Once reconstituted, verify the in-use window against your own vial's documentation rather than assuming it matches another compound.
As with any lyophilized research peptide: keep the sealed powder vial frozen until use, store the reconstituted solution refrigerated (2–8°C), keep it out of direct light, and avoid repeated freeze-thaw. Draw with a fresh sterile syringe each time. Discard if the solution becomes cloudy or shows particulates.
Reading your insulin syringe
All three insulin syringes are U-100, where 1 mL = 100 units. The tick resolution differs: a 0.3 mL (30 u) and 0.5 mL (50 u) syringe print 1 unit per tick, but a 1 mL (100 u) syringe prints 2 units per tick — so ten ticks is twenty units, not ten. Always read against the front edge of the plunger seal. The visualizer in the calculator above marks the exact fill position for your result.
Common mistakes
- Shaking the vial. Shaking foams the solution and can degrade the peptide. Swirl gently and let it settle.
- Misreading a 1 mL syringe. Each tick is 2 units on a 1 mL barrel — the single most common measuring error.
- Too little diluent. Reconstituting a large vial in too little water makes the draw tiny and hard to measure. Add more bacteriostatic water for a readable draw.
- Using the wrong water. Bacteriostatic water (with benzyl alcohol) is the diluent for multi-use vials; sterile water has no preservative.
For the full walkthrough with every step photographed out, see the complete how-to-reconstitute-peptides guide. For ratios, shelf life, and storage specifics on the diluent itself, see the bacteriostatic water guide.
HGH (Somatropin) reconstitution, answered.
How many IU is 1 mg of HGH?
The WHO international standard for somatropin is 3 IU per mg, so 1 mg is about 3 IU and 10 IU is about 3.33 mg. This calculator works in mg — convert your vial's IU label to mg first, then enter it above.
Why does this calculator use mg instead of IU for HGH?
The underlying math (concentration = mg ÷ mL) is the same for every compound on this site, so it is built around milligrams. HGH vials are conventionally labeled in IU, so convert first: divide the IU on your vial by 3 to get mg (10 IU is about 3.33 mg), then enter that figure above.
How much bacteriostatic water for a 10 IU HGH vial?
Researchers commonly use 1–2 mL for a 10 IU (about 3.3 mg) vial. 1 mL gives a more concentrated, smaller draw; 2 mL gives a larger, easier-to-read draw. Enter the mg equivalent and your chosen water volume above.
How do you reconstitute HGH (Somatropin)?
Add bacteriostatic water slowly down the inside wall of the vial, let the white lyophilized powder dissolve without shaking, and read the concentration as vial mass ÷ water volume. The calculator above turns your vial mass, water volume, and target research quantity into a draw volume and U-100 syringe units.
Is this a dosing calculator?
No. This is a reconstitution and concentration calculator for in-vitro laboratory research. It does not provide medical advice, is not intended for human use, and does not establish a dosing recommendation.
Other compounds.
Reference materials you can verify.
Look for an independent Certificate of Analysis on every lot, third party testing, and lot traceability. Verify the source the way you verify the numbers here.
See COA verified materials