Reconstitute Melanotan II.
Free Melanotan II reconstitution calculator. Enter your vial mass and bacteriostatic water for the concentration, draw volume, and exact U-100 syringe units, with a live syringe visualizer. Research use only.
What are you reconstituting?
/How many milligrams are in your vial?
How much bacteriostatic water are you adding?
How much do you want per aliquot?
Which insulin syringe do you have?
Add vial cost for cost per aliquot
Reference figures. Verify all calculations independently before laboratory use. 1 mL = 100 U-100 units. This tool does not recommend a dose, frequency, or protocol.
How to reconstitute Melanotan II.
Melanotan II is a synthetic analogue of the peptide hormone alpha-MSH, supplied as a lyophilized research powder.
- Add bacteriostatic water. Swab the tops of both the Melanotan II vial and the bacteriostatic water vial. Draw your chosen water volume, then inject it slowly down the inside wall of the Melanotan II vial so it runs onto the powder rather than splashing onto it.
- Let it dissolve. Let the Melanotan II dissolve on its own, swirling gently if needed. Do not shake — shaking foams the solution and can stress the peptide. Within a minute or two you should have a clear solution (white-to-pale lyophilized powder dissolves to a clear liquid).
- Read the concentration. Your concentration is the vial mass divided by the water you added. 10 mg in 2 mL of bacteriostatic water is 5 mg/mL (5,000 mcg/mL). Enter your own numbers in the calculator above to get the draw volume and U-100 syringe units for any research quantity.
Bacteriostatic water and concentration
The volume of bacteriostatic water you add is the only thing that sets the concentration — the vial mass is fixed. More water means a lower concentration and a larger, easier-to-measure draw. Here is how common Melanotan II vial sizes land at a 2 mL fill:
| Vial mass | BAC water | Concentration | (mcg/mL) |
|---|---|---|---|
| 10 mg | 2 mL | 5 mg/mL | 5,000 mcg/mL |
Researchers commonly use 1–3 mL of bacteriostatic water for Melanotan II. Any volume in that range works; it only changes how concentrated the vial is and how large the draw will be.
Storage, stability and handling
- Melanotan II is commonly supplied in 10 mg vials.
As with any lyophilized research peptide: keep the sealed powder vial frozen until use, store the reconstituted solution refrigerated (2–8°C), keep it out of direct light, and avoid repeated freeze-thaw. Draw with a fresh sterile syringe each time. Discard if the solution becomes cloudy or shows particulates.
Reading your insulin syringe
All three insulin syringes are U-100, where 1 mL = 100 units. The tick resolution differs: a 0.3 mL (30 u) and 0.5 mL (50 u) syringe print 1 unit per tick, but a 1 mL (100 u) syringe prints 2 units per tick — so ten ticks is twenty units, not ten. Always read against the front edge of the plunger seal. The visualizer in the calculator above marks the exact fill position for your result.
Common mistakes
- Shaking the vial. Shaking foams the solution and can degrade the peptide. Swirl gently and let it settle.
- Misreading a 1 mL syringe. Each tick is 2 units on a 1 mL barrel — the single most common measuring error.
- Too little diluent. Reconstituting a large vial in too little water makes the draw tiny and hard to measure. Add more bacteriostatic water for a readable draw.
- Using the wrong water. Bacteriostatic water (with benzyl alcohol) is the diluent for multi-use vials; sterile water has no preservative.
For the full walkthrough with every step photographed out, see the complete how-to-reconstitute-peptides guide. For ratios, shelf life, and storage specifics on the diluent itself, see the bacteriostatic water guide.
Melanotan II reconstitution, answered.
How do you reconstitute a 10 mg Melanotan II vial?
Add bacteriostatic water slowly down the vial wall and let it dissolve. 10 mg in 2 mL is 5 mg/mL (5,000 mcg/mL). Enter your target quantity above for the draw.
How do you reconstitute Melanotan II?
Add bacteriostatic water slowly down the inside wall of the vial, let the white-to-pale lyophilized powder dissolve without shaking, and read the concentration as vial mass ÷ water volume. The calculator above turns your vial mass, water volume, and target research quantity into a draw volume and U-100 syringe units.
Is this a dosing calculator?
No. This is a reconstitution and concentration calculator for in-vitro laboratory research. It does not provide medical advice, is not intended for human use, and does not establish a dosing recommendation.
Other compounds.
Reference materials you can verify.
Look for an independent Certificate of Analysis on every lot, third party testing, and lot traceability. Verify the source the way you verify the numbers here.
See COA verified materials