Blend Calculator

Peptide blend reconstitution calculator.

Reconstitute a multi-peptide blend vial — BPC-157 + TB-500, CJC-1295 + Ipamorelin, or any combination — by treating the combined vial mass as one number. Research use only.

Step 1 of 6 Compound Live

What are you reconstituting?

/
Pick the compound you are reconstituting. Not on the list? Choose Custom compound at the bottom and enter your own vial size.
Compoundselected

How many milligrams are in your vial?

Look at your vial label for the total mg of lyophilized (freeze dried) powder. This is the whole amount in the vial, not a portion. Common sizes for this compound are shown above.
▶ How to read your vial
Compoundvial

How much bacteriostatic water are you adding?

That makes a concentration of2.5mg/mL
Bacteriostatic water is the sterile liquid you mix into the vial. More water = lower concentration = a bigger, easier to measure draw. The range above is what researchers commonly use for this compound. Anything in it works, it just changes how concentrated the vial is.
▶ How to add BAC water
Compoundamount

How much do you want per aliquot?

The research quantity you want in each measured portion, called an aliquot. Switch between mcg (micrograms) and mg (milligrams) to match how you think about it.
Compoundsyringe

Which insulin syringe do you have?

Pick the insulin syringe you will draw with. All are U-100. On a 1 mL (100 unit) syringe each printed tick is 2 units, not 1. On 0.3 mL and 0.5 mL syringes each tick is 1 unit.
▶ How to read an insulin syringe
Compoundresult
Draw, U-100 units
10u
Draw volume
0.100mL
Concentration
2.5mg/mL
Aliquots / vial
20
Cost / aliquot
n/a
Draw to the 10 unit mark on your 0.5 mL syringe. Verify the figures independently before laboratory use.
▶ Watch the full reconstitution walkthrough
Add vial cost for cost per aliquot
Get the free Reconstitution Reference Card
22 compounds, BAC-water ratios, syringe units, and storage windows — one printable PDF.
Or just download the PDF ↓

Reference figures. Verify all calculations independently before laboratory use. 1 mL = 100 U-100 units. This tool does not recommend a dose, frequency, or protocol.

A peptide blend is a single vial containing two or more lyophilized peptides freeze-dried together — for example BPC-157 + TB-500 or CJC-1295 + Ipamorelin. Reconstituting a blend is no harder than a single peptide: you treat the combined vial mass as one number.

How a blend calculates

The vial label lists the total milligrams of all the peptides combined. That total, divided by the bacteriostatic water you add, is the total peptide concentration per millilitre. The calculator above works on that total — enter the combined mg printed on the vial, not one peptide's share.

Blend vial (total)2 mL BAC water3 mL BAC water
10 mg5 mg/mL3.33 mg/mL
15 mg7.5 mg/mL5 mg/mL
20 mg10 mg/mL6.67 mg/mL

Worked example: a 10 mg blend vial (the combined total of both peptides) reconstituted in 3 mL of bacteriostatic water is 3.33 mg/mL of total peptide. A 250 mcg draw of total peptide is 250 ÷ 3,330 = 0.075 mL = 7.5 units on a U-100 syringe. Run your own combined mass through the calculator for the exact figures.

What a blend draw actually contains

Because the peptides are dissolved together in one solution, every draw contains both, in whatever ratio the vial was blended (for instance a 1:1 or 2:1 BPC-157:TB-500 blend). The calculator gives you the total-peptide concentration and draw volume; the specific ratio of one peptide to the other is set by the manufacturer and printed on the vial.

Common research blends

For single compounds, see the full list of per-compound calculators, or the step-by-step how-to-reconstitute-peptides guide.

FAQ

Common questions, answered.

How do you calculate a peptide blend like BPC-157 + TB-500?

Use the combined milligrams printed on the vial as a single mass. A 10 mg blend vial (total of both peptides) in 3 mL of bacteriostatic water is 3.33 mg/mL of total peptide. Enter that combined mass and your water volume in the calculator for the draw volume and U-100 syringe units.

Does each draw from a blend contain both peptides?

Yes. The peptides are dissolved together in one solution, so every draw contains both in the ratio the vial was blended. The calculator gives the total-peptide concentration; the specific ratio is set by the manufacturer and printed on the vial.

How much bacteriostatic water should you use for a blend vial?

The same principle as a single peptide: the water you add sets the concentration. Blends often use a slightly larger volume (2–3 mL) because the combined vial mass is higher, which keeps the draw large enough to measure accurately.

Can you calculate the two peptides in a blend separately?

If the vial lists each peptide’s mass and ratio, you can compute each one’s individual concentration. For the draw itself you only need the combined total, since both peptides come out together in every draw.

Is this a dosing calculator?

No. This is a reconstitution and concentration calculator for in-vitro laboratory research. It does not provide medical advice, is not intended for human use, and does not establish a dosing recommendation.

Calculators

Every compound.

How these figures are verified. The formulas used here are standard and independently checkable: concentration = vial mass (mg) ÷ bacteriostatic water (mL); draw volume = research quantity ÷ concentration; U-100 units = draw volume (mL) × 100. Every result updates live and can be reproduced by hand or against published reconstitution references from R&D Systems and Tocris. This page covers reconstitution technique and handling only; it does not recommend a dose, frequency, or protocol. Reconstitute Editorial · Methodology · Last reviewed 2026-10-15
Sourcing

Reference materials you can verify.

Look for an independent Certificate of Analysis on every lot, third party testing, and lot traceability. Verify the source the way you verify the numbers here.

See COA verified materials